Cable tie
Through the slot in a cable tie’s head, the toothed nylon tail goes one way only. Inside the head, a springy catch called the pawl lets the teeth pass going in and holds them coming back.
One piece of nylon
A cable tie, or zip tie, is a strip of nylon with a row of small teeth along one side and a head at one end with an opening through it. Inside the opening sits the pawl, a short wedge whose face carries teeth shaped to fit the strap’s. Jack E. Caveney’s patent of 1970, filed for Panduit, calls this kind of tie integral and one-piece. Every part of it is moulded in one piece with the parts beside it, from a plastic resin, preferably a polyamide. Caveney calls the head a frame.
The pawl has no pin and no spring of its own. A narrow neck joins it to the thick end of the strap and bends like a hinge, and that neck is its spring too. HellermannTyton moulds the pawl as part of the tie in 90% of the polyamide ties it supplies, and Panduit still calls its ties a “one-piece design with locking wedge”.
Pulling the tail through
As moulded, Caveney’s pawl stands up out of the head with its teeth at about 45° to the strap. Its nearest point is 0.040 inch (1.0 mm) from the end wall across the opening. The strap is thicker than that gap. So the tail, pushed in through the head’s lower face, is guided by the pawl’s underside into the gap and pushes the pawl back as it goes.
The pawl has to be flexible enough to see-saw over the strap’s teeth without breaking, yet stiff enough for its own teeth to catch them. The head in Fig. 1 is drawn to the sizes of Caveney’s example tie, whose teeth are 0.030 inch (0.76 mm) apart. Pull the tail up, then let go. Before you let go, guess how far the strap slides back before the pawl holds it.
What the drawing shows
The strap never slides back more than 0.85 mm in the drawing, a little more than one tooth. While you pull, the pawl touches the strap at one corner only, the foot of its lowest tooth. Each tooth pushes that corner open, so the pawl stands 1.4° to 4.3° further open than it was moulded. Every 0.76 mm the corner drops behind a tooth. Let go, and the strap slides back until the corner sits in a gap and the tooth above comes down on it.
That tooth pushes along its own sloping side. The push turns the pawl toward the strap, so the pawl presses in. It cannot turn in any further without cutting into the tooth below, and it cannot turn out against the tooth above. The corner is jammed. The strap stops. Caveney wrote that any pull on the strap only drives the pawl’s teeth harder into the strap’s, wedging the strap against the end wall. All of these lengths and angles come from the drawing’s model.
Water and sunlight
Polyamide takes water from the air and gives it off again, and the water changes how flexible and strong it is. At 23 °C and 50% humidity it holds about 2.5%. That is the amount that lets the pawl see-saw as it should, and once the tie has locked, a change in water hardly matters. Ties keep best in their sealed bag, away from heat and direct sun. Panduit gives its nylon 6.6 ties a water uptake of 1.2% in 24 hours. Their top working temperature is 85 °C, and the lowest for fitting them is minus 60 °C.
On The Garage Journal forum, readers said that some of their ties broke straight out of the packet, snapping in two when bent. One wrote that nylon gets brittle when it dries out and that soaking ties in water makes them like new.
Another reader there found that black ties hold up better in the sun than white ones. HellermannTyton says the colour is not enough. A black tie of ordinary polyamide 6.6 holds only a little carbon black, while its ties for outdoors hold about 2%. Its test is to flatten the end of the tail with a hammer and hold it to the light. A tie with 2% lets no light through.
A steel ball for a pawl
Some ties hold the strap with other parts. ABB’s Ty-Rap ties have a smooth body and a locking device of 316 stainless steel in the head. HellermannTyton’s releasable ties keep the pawl but give it a long tab, pushed with a finger to let the strap go.
HellermannTyton’s stainless steel ties have no teeth at all. The strap runs straight through the head under a small ball, and the ball locks it by moving into the small end of a wedge-shaped housing. Fig. 2 draws that idea, and its ball rides on the strap until it touches the housing. Before you let the steel strap go, guess whether it holds at once.
What the drawing shows
It slides back first. In the drawing it goes 1.58 mm, while the ball rides back from the wide end until it touches the roof. Round a rigid object such as a metal pipe, the ball may not get back into the small end, so a protective channel goes between strap and pipe.
Waxed cord and hamburger hands
In 1956 Maurus Logan of Thomas & Betts toured a Boeing factory and saw aircraft wiring laid out on sheets of plywood 50 feet long. Knotted, wax-coated, braided nylon cord held the wires. Workers pulled each knot tight by wrapping the cord round a finger. It cut them until they grew thick calluses, “hamburger hands”.
Logan filed his patent on 24 June 1958, and it was granted on 27 February 1962. It describes the old way. Each tie was a separate piece of waxed twine or nylon cord, looped twice round the wires and knotted, which took a great deal of time. The wax kept the knot from untying and was a possible fire hazard.
His strap has no pawl. Moulded of nylon with an oval cross-section, it is held by friction in an eyelet of the same shape. For an extra lock the patent offers a tooth cut part-way out of the strap by a special pliers-like tool, or a small metal plate with two ears that bite into the strap if it moves back. Among the earlier patents it lists is a rubber hair curler of 1908, whose studded tip went through a hole in its own head.
ABB says it invented the Ty-Rap in 1958. The National Inventors Hall of Fame calls the Ty-Rap the first self-clinching cable tie, with a stainless steel locking device in its head. In Logan’s patent the metal plate is a separate piece, slipped over the tail once it is through. Caveney filed for his one-piece tie in 1968.
What the drawings leave out
The sizes are the drawing’s own. No tie was measured, and neither drawing cuts through the side walls of a head. In Fig. 2 the ball and the slope of the roof are drawn with no maker’s figure for them, and so is the rule that the ball rides with the strap until it touches the housing.
In Fig. 1 nothing bends except the pawl’s neck. Real nylon teeth give a little. Caveney wrote that once the bundle pulls on the strap, the pawl swings down into the head until its teeth lie along the end wall, all of them loaded, with its top flush with the head. The drawing’s rigid pawl stops where its corner first jams. Its strap is straight and pressed flat on the end wall, while a real one comes up from a loop round the bundle.
Fig. 1’s teeth, strap, head and moulded gap follow Caveney’s example tie, and the height of the hinge follows from them. No source gives the shape of the pawl’s back or the stiffness of its neck.
Sources
Read in November 2026.
- J. E. Caveney, for Panduit, US Patent 3,537,146, “Integral one-piece cable tie”, 1970: Fig. 1 follows its words and its example’s sizes.
- M. C. Logan, for Thomas & Betts, US Patent 3,022,557, “Cable bundling and supporting strap”, 1962.
- W. F. Schacht, US Patent 876,402, “Hair-curler”, 1908.
- ABB, “How the Ty-Rap was invented”, and its brochure “The Original Oval”, 2018.
- National Inventors Hall of Fame, Maurus Logan, inducted in 2026.
- HellermannTyton, “Cable Ties and Fixings”, chapter 1, January 2018: its technical pages, 27 to 35, and releasable ties, pages 73 and 77.
- Panduit, “Antimicrobial Nylon 6.6 Cable Ties”, specification sheet, April 2023.
- The Garage Journal forum, “Ran out of wire ties”, February 2022. User report.
The type is Playpen Sans by TypeTogether, under the SIL Open Font License 1.1.