Derailleur
Gear changes on a bicycle move its chain sideways, while it runs, from one sprocket on the back wheel to the next. The derailleur hangs below the sprockets, an arm carrying two small toothed pulleys that the chain runs round in an S. A cable from the gear lever pulls the arm inwards, and a spring brings it back out.
Seven sprockets on one hub
Seven sprockets stand side by side on the back wheel of a seven-speed bicycle. On Shimano’s MF-TZ500 they have 14, 16, 18, 20, 22, 24 and 28 teeth, and the figures on this page use those seven. The set is called a multiple freewheel, a freewheel like the one on the Freewheel page with seven sprockets in place of one. The smallest is on the outside, furthest from the spokes. The derailleur sits further out still, fixed to the frame beside the wheel.
Every sprocket takes one chain. KMC’s Z7 chain for seven speeds is 1/2 by 3/32 inch. The first number is the pitch, the distance from one pin to the next, and the second is the width between the inner plates. A pitch of 12.7 mm fixes how big each sprocket is. The chain’s pins go round a circle 57.1 mm across on the 14-tooth sprocket and 113.4 mm across on the 28. With a 36-tooth chainring in front, one turn of the cranks turns the 14-tooth sprocket 2.57 times and the 28-tooth one 1.29 times.
From the lever to the cage
In 1986 Masashi Nagano patented a rear derailleur for Shimano. It is a small linkage. A base member is fixed to the frame, two links swing on it, and a movable member rides on their free ends. The links stay parallel. So the movable member slides across without tilting. That keeps the cage lined up with the chain. The cage, Nagano’s chain guide, hangs from the movable member and carries the guide pulley and the tension pulley.
The cable pulls the movable member inwards, toward the largest sprocket, against a return spring. When the cable is let go, the spring brings it back to the smallest. This kind is called high normal. A gear lever with clicks stops the cable after a set length each time, and in Fig. 1 the seven clicks sit where the guide pulley is under each sprocket. Guess whether one click puts the chain straight onto the next sprocket.
What the drawing shows
The guide pulley moves at once, but the chain stays on its sprocket. Its run up from the guide pulley now leans across from one sprocket’s plane to the next, and nothing more happens until the chain moves. Nagano’s patent says the lever can be set “even when the chain is not driven by pedalling”, and the chain shifts once it is pedalled.
In the drawing each click pulls 2.4 to 2.9 mm of cable and moves the cage 5 mm, so the cage goes about twice as far as the cable. No maker’s document read for this page gives such figures for a real derailleur.
Onto the next sprocket
From the chain side, the chain leaves the top of a sprocket for the chainring and comes back underneath. It runs round the tension pulley, then the guide pulley, and climbs onto the back of a sprocket again (Fig. 2). The links that arrive from the guide pulley are the only ones the derailleur can lead.
Nagano’s 1989 patent for Shimano describes the climb. The derailleur pushes the chain toward the larger sprocket. The two sprockets are set so that a gap between teeth on the larger one and a gap on the smaller one lie on one straight line along the chain’s path, a whole number of links apart. The chain crosses there. In Fig. 2 the new links go onto the new sprocket, and the straight crossing turns with the sprockets until it reaches the top. Click the lever once in Fig. 2, then guess how far the cranks must turn before the whole chain is on the new sprocket.
What the drawing shows
The climb from the 14-tooth to the 16-tooth sprocket takes 50° of the crank in the drawing, about 64 mm of chain.
Riders argue, in user reports, about how hard to pedal while this happens. A rider on Bicycles Stack Exchange had been told to speed up, stop pedalling, shift, then pedal lightly until the chain moved. The accepted answer said a shift twists the chain with a brief push from the side. A chain bends easily one way, it added, but only a little sideways. Another answer said the best shift comes with almost no weight on the pedals. With the lever pulled all the way at once, the chain still climbs one sprocket at a time and reaches the 28 after the cranks have turned 1.13 times.
Taking up the slack
Sheldon Brown’s glossary calls the upper pulley the jockey and the lower one the tension pulley. The two can look alike. In one user report, a rider on Bicycles Stack Exchange who had taken a derailleur apart to clean it found that one pulley had a metal bushing and was “a bit beefier”. The answer said that one goes on top. It is the pulley that “shifts the gears”. The lower one only keeps the chain tensioned.
A bigger sprocket takes more chain round it, and the chain cannot change length. The rear derailleur takes up the slack, sitting in the chain’s lower, slack run. Nagano’s cage turns on the movable member, and a spring between them swings the tension pulley back to keep the chain taut. The chain in Fig. 2 is 76 links long. On the 14-tooth sprocket the cage hangs 17° back of straight down, and on the 28-tooth one it swings 37° forward.
Earlier ways to move a chain
Gears with several sprockets in a row are older than the word. In a US patent of 1899, from a British one of 1896, Edmund Hugh Hodgkinson of London set “two or more pinions of different sizes” side by side on the back wheel. He made “arrangements … for shifting the driving-chain from pinion to pinion”. His chain stayed in line. A chain lifter raised it, the pinions slid along their spindle, and the lifter set the chain down on the new one, “while riding”.
A mechanic’s post on Reddit’s r/bikewrench, a user report, asked why derailleurs whose parallelograms lean differently shift differently. A reply said the designs differ in how closely the upper pulley follows the sprockets as it sweeps across. Another said a big gap between pulley and sprockets made shifts slow and noisy with friction levers.
For the derailleur’s own history, Wikipedia is the only source read here. It says Paul de Vivie, a French cycle tourist who wrote as Velocio, invented a two-speed rear derailleur in 1905, and that Shimano brought in indexed shifting in 1985.
What the drawings leave out
The sizes are the drawing’s own. Only the tooth counts and the chain’s pitch come from real parts. The sprockets are 5 mm apart, and the pulleys have 11 teeth. The chainring has 36 and sits far closer to the wheel than on a bike, and the crank is short. The linkage in Fig. 1 swings flat in the view from behind, as if its pivots pointed straight forward. On a real derailleur they lean. In the drawing the links bring the guide pulley lower for the larger sprockets by rising toward the wheel.
Fig. 2 leaves out the derailleur’s body and the near plate of the cage, and the cage turns on the guide pulley’s axle. Neither figure draws the shapes of the teeth, or the recess Nagano’s 1989 patent cuts in the larger sprocket to let the chain across. The chain is rollers alone, and its crossing is a straight line between two circles. By the model’s own rule, each crossing starts where the chain’s path does not jump, but where one ends the cage can still swing about 2° in a degree of crank. The front derailleur, which moves the chain between chainrings, is not drawn.
Sources
Read in November 2026.
- M. Nagano, US Patent 4,612,004, “Rear derailleur for a bicycle”, Shimano Industrial Company, 16 September 1986. Its words only.
- M. Nagano, US Patent 4,889,521, “Multistage sprocket assembly for a bicycle”, Shimano Industrial Company, 26 December 1989. Its words only.
- E. H. Hodgkinson, US Patent 617,572, “Changeable gearing for vehicles”, 10 January 1899.
- Shimano, parts sheets for the Tourney RD-TY500 derailleur (2019) and the MF-TZ500 freewheel (2017), and its MF-TZ500-7 product details, for the tooth counts.
- KMC, Z7 chain, for the chain’s size.
- Wikipedia, “Derailleur” and “Bicycle chain”.
- Sheldon Brown, Bicycle Glossary, “Pulley”.
- Bicycles Stack Exchange, “Which pulley is which on my Shimano STX RC derailleur?”, April 2013, and its answer. User report.
- Bicycles Stack Exchange, “How bad is switching derailleur gears under load?”, May 2021, and two of its answers. User report.
- r/bikewrench, “Question about different derailleur geometries - traditional parallelogram vs drop vs drop-slant”, October 2015, via the Arctic Shift archive. User report.
- Bartosz Ciechanowski, “Bicycle”: the forces in the chain and the rest of a bicycle, which this page does not cover.
The type is Playpen Sans by TypeTogether, under the SIL Open Font License 1.1.