Keyboard key
Hollow cones of rubber stand under the keys of a rubber dome keyboard, a small one under each key. Each cone springs the key back up and, near the end of the key’s travel, closes the switch by pressing three thin plastic sheets together.
A rubber cone over three sheets
The part under your finger is the keycap. A stem hangs from it, and the stem’s plunger slides up and down in a bore. The bores belong to one moulded frame, called the monoblock. Below the frame lies a sheet of rubber with a dome at every key. Each dome is the key’s return spring and keeps dirt off the switch. Its base stands on the switch, and its truncated cone is made to buckle as the key goes down.
The switch itself is three layers of thin plastic. Most such switches have a flexible upper layer and a flexible lower layer with a spacer sheet between them. Key Tronic’s patent of 1995 makes each about 0.004 inch thick. The spacer is holed at every key. Inside the dome’s top hangs a short wall, the membrane switch actuator. When the dome gives way, the actuator presses the upper layer down through the hole and onto the lower one, where printed contacts meet. On this page the three layers are the top sheet, the spacer and the bottom sheet.
Cherry called boards like these foil keyboards with rubber mats. Collectors call the design rubber dome over membrane, and the whole board a membrane keyboard. It is the most common keyboard design made today.
A force that climbs and then gives
Cherry’s catalogue for 2006 and 2007 draws, for each kind of keyboard it made, the force on a key against how far the key has gone down. It gives the force in centinewtons. One centinewton is roughly a gram’s weight. For its rubber mat keyboards the force climbs fast at first and then more slowly, to about 56 cN some 1.15 mm down. Cherry calls that place the tactile point. Past it the dome gives way, and the force falls to about 30 cN at 2.75 mm. Fig. 1 draws Cherry’s curve beside the key. Guess where the contacts close: on the bump’s crest, at its lowest point, or somewhere else.
What the drawing shows
The contacts close at 3.0 mm, where Cherry marks the operating point, a quarter of a millimetre past the lowest force. Nagurka and Marklin, at Marquette University, pressed the keys of 22 rubber-dome keyboards from four makers with a machine. Pressed slowly, the force peaked about 1.3 mm down and was lowest about 2.5 mm down, then rose as the key began to bottom out. They note that the standard ISO 9241-4 calls this a snap-action key, one that must switch at a force no higher than its peak. A patent granted to Fujitsu Component in 2021 has its contact close while the force is still falling, before the lowest point, so that the feel matches the switching. Cherry’s diagram puts the closing just after it. Fig. 1 follows Cherry. After 3.5 mm the curve climbs steeply as the key bottoms out.
A tenth of a millimetre
Fig. 2 draws the middle of the three sheets about six times larger than Fig. 1 does, with the actuator above them, from 2.80 mm to 3.10 mm of the key’s travel. Before you lower it, guess how far the top sheet must bend for its contact to reach the one below.
What the drawing shows
The top sheet bends 0.1 mm, the thickness of the spacer and Key Tronic’s 0.004 inch. That is a fortieth of the key’s 4 mm. The dome takes all the rest. Keyboard collectors on the Deskthority wiki measured one keyboard’s top and bottom sheets at about 0.06 mm and its spacer at 0.09 mm. With the domes taken off, a stack of four to six five-pence coins, 13 to 19.5 g, closed a contact. The same keyboard’s keys took 65 to 75 g with their domes in place.
On the Deskthority forum, in posts that are user reports, one collector asked whether a dome key must really go all the way down to switch, since every force curve the collector had seen put the switching before full travel. A reply said the bump makes you press harder, so you nearly always reach the bottom anyway. Wikipedia says the dome must be fully pressed down for the contacts to meet. Cherry’s operating point is a millimetre short of the end.
Letting the key back up
Cherry draws a second curve under the first for the key’s return. Coming up, the dome pushes with at most about 47 cN and at its weakest with 22 cN. The keyboards pressed by machine pushed back less on release, too, all through the travel, which their testers put down to friction.
Makers of rubber keypads for other machines give the bump a number, the snap ratio. It is the drop from the peak to the force at contact, divided by the peak. One keypad maker’s design guide recommends about 40 to 60%, and a return force of 30 to 35 g “to ensure that keys do not stick”. It adds that “the higher the force, the longer the life but the poorer the tactile response”. Its numbers are for keypads. For Cherry’s key the drop is 44% of the peak.
A Super User question, a user report, describes a used folding keyboard whose keys stayed down. Under the keycaps the domes were stuck in the down position, and the asker thought the rubber was old. The collectors’ site Telcontar.net says that domes stiffen with age, so old keyboards take more and more force, that some go limp instead, and that domes can split from fatigue. Singer’s patent of 1970, for a rubber boot round a key stem, says the boot acts like a toggle with two stable states. Pressed past a balance point, it would stay down when let go, so the key has a stop that halts it short of that point.
Notebook keys
A study of typing force measured three keyboards from one maker. On its rubber-dome desktop keyboard the force peaked at 0.68 N, about 1.10 mm down. On its notebook the peak was 0.59 N, only 0.75 mm down. Its third, a desktop board with spring columns, peaked at 0.86 N. As far as the study’s authors knew, notebook keyboards use only rubber dome keys. Typists in the same study pressed the desktop’s rubber-dome keys with 1.54 N on average. That is 2.2 times the peak.
In Fujitsu Component’s patent, two gear links joined by teeth hold the key top over a dome on a membrane sheet. The links “guide the key top 10 in the vertical direction while keeping the key top 10 horizontal”. At rest they stand in a reverse V, and their rear ends slide sideways as the key goes down. Keys of this kind are called scissor-switches, after two plastic pieces that interlock like scissors.
Older rubber
Olson’s patent for Singer, filed in April 1970 and granted in October 1973, describes a rubber boot whose force rises to a maximum and then falls. It calls the fall a breakaway feel. The patent says the feel was found in electric typewriters and had been had in other keyboards only with costly and complex mechanisms. With it, the typist can start on the next key sooner. Telcontar.net points to this patent and to an earlier one, Friden’s “Optical encoder” of 1967, as already having a rubber dome.
Sobol’s patent for Texas Instruments, filed in February 1980 and granted in October 1982, puts the dome over the plastic sheets. Its domes are silicone rubber about 70 on the Shore A scale, with walls five to ten thousandths of an inch thick, and its keys travel 50 to 125 thousandths. The patent found that long travel right for business calculators. Its claim keeps the spacer thin, while each dome is “deformed to a relatively much greater extent to provide long travel and high tactile feedback”. Telcontar.net also writes that Cherry in the United States advertised a keyboard with a “dome-shaped silicone elastomer layer” in 1984. The Deskthority wiki says membrane keyboards became common only in the 1990s. By the 2000s, it says, rubber dome over membrane was a given. The reason was cost, as the price of computers fell.
What the drawings leave out
The sizes are the drawing’s own. The shapes of the dome, the keycap and the frame have no source. Only the key’s travel, the place where the contacts close and the sheets’ thickness come from sources. The force is Cherry’s, for its rubber mat keyboards, read off its printed diagram to within about 2 cN, and another keyboard has its own numbers. Fig. 2 draws only the middle of the switch, where the actuator presses. In the drawing the dome’s wall stays straight and shortens until the force peaks, then bends as an arc of fixed length. A real wall bends from the start. The last millimetre goes into squeezing the actuator alone, where a real key squeezes the folded wall too. Cherry gives no separate place where the contacts open on the way up, so the drawing opens them where they closed. Turn the key round partway down and the dot jumps straight from one curve to the other.
Sources
Read in November 2026.
- Cherry GmbH, its keyboard catalogue for 2006 and 2007, pages 8 and 9, through the Deskthority wiki’s copy. Both figures follow its curves for rubber mat keyboards.
- D. A. Burgett, Key Tronic, US Patent 5,684,279, “Computer keyboard with improved membrane keyswitch structure having deflection concentration feature”, filed 12 September 1995, granted 4 November 1997.
- A. J. Sobol, III, Texas Instruments, US Patent 4,354,068, “Long travel elastomer keyboard”, filed 4 February 1980, granted 12 October 1982.
- C. G. Olson, The Singer Company, US Patent 3,767,022, “Return spring key stem boot”, filed 24 April 1970, granted 23 October 1973.
- S. Okutani, Fujitsu Component, US Patent 11,004,627, “Reaction force generating member and key switch device”, granted 11 May 2021.
- Diamond HMI, its rubber keypad design guide.
- M. Nagurka and R. Marklin, stiffness and damping of keyboard keys, 2005; M. J. Bufton, R. W. Marklin, M. L. Nagurka and G. G. Simoneau, desktop and notebook key stiffness and typing force, Ergonomics, 2006.
- Wikipedia, “Keyboard technology”, for the common design, the scissor-switch and the claim about full travel.
- D. Beardsmore, Telcontar.net, “Rubber domes”. User report.
- Deskthority wiki, “Membrane keyboard”. User report.
- Deskthority forum, a thread on full travel, November 2017. User report.
- Super User, “How to restore rubber dome keyboard membrane springiness?”, June 2019. User report.
The type is Playpen Sans by TypeTogether, under the SIL Open Font License 1.1.