Howthings

Light switch

Behind the cover plate of a wall light switch, a spring holds the contacts either pressed together or held apart. Push the toggle slowly, and the lamp stays as it was until the toggle reaches the middle of its travel. Then the contacts jump across, faster than your finger moved.

A push that moves nothing

The toggle you press is not fixed to the contacts. A spring and levers sit between them, and for the first part of a push the spring goes on holding the contacts where they were. Meanwhile the push loads the spring. Once the parts pass their centre point, the spring, not your finger, drives the contacts to the other side with the snap you hear.

Fig. 1 is a simplified toggle switch, cut through from the side. The toggle turns on a pin just behind the cover plate, so when you push its handle up, its tail inside the box goes down. A spring in the tail pushes a small cap against a contact bar, which rocks on a pivot of its own. With the cap above the pivot, the top of the bar rests against a stop. With the cap below it, the bottom of the bar rests on a fixed contact, and the lamp is on.

Now try Fig. 1. Before you drag the toggle up, guess where along its travel the lamp will come on.

A toggle switch cut through from the side, with the toggle downtogglespringbarstopcontactcover plate
Fig. 1 A simplified switch cut through from the side. The cover plate runs down the left, with the box behind it, and the sides of the box, which hold the two pivots, are cut away. Watch the spring and the bar. Not to scale.
What the drawing shows
A toggle switch seen from the side and cut through. On the left the toggle’s handle sticks out of the cover plate’s slot; it turns on a pin just behind the plate. Its tail, inside the box, holds a spring with a small cap on the end, and the cap presses on a contact bar that rocks on a pivot. Above the pivot the bar can rest against a stop, and below it against the fixed contact. As the toggle moves toward level the spring gets shorter, and the bar stays put. Once the toggle passes level, the bar tips across.

The lamp comes on just as the toggle passes level, halfway through its travel. Before that, the bar never moves. All the way up, the cap presses above the pivot, so the bar stays against the stop while the spring gets shorter. In the drawing the spring is 24% shorter at level than at either end. Just past level, the cap’s line crosses the pivot. The squeezed spring now pushes the bottom half of the bar, and the bar tips onto the contact in one jump.

Sparks between parting contacts

A slow switch would be hard on its contacts. When enough current is flowing and two contacts begin to part, the current goes on across the first small gap and turns the air there into an arc, a path of hot, charged gas that conducts well. The arc can keep the current flowing while the gap grows. It is very hot, and the heat eats into the metal. With a high enough voltage, an arc can also jump across just before two contacts close.

The usual cure is a spring that tips over a point and moves the contacts fast, however slowly the lever goes. Alternating current helps as well. It falls to zero again and again, which makes an arc harder to keep going as contacts open. By Wikipedia’s account, arcing in early switches pitted one contact and left a crust of residue on the other, so the switch soon wore out.

Holmes’s quick break

John Henry Holmes, of Newcastle upon Tyne, set the problem out in his US patent of September 1884. In every switch he knew of, he wrote, the contacts slid against each other all the way, or the handle was fixed to the contact piece. Turned slowly to break the circuit, such a switch drew a destructive arc. His answer was to let the contact piece travel a short way on its own, driven by a spring.

Fig. 2 shows his switch from above. A contact bar swings on the same axis as the handle. When the switch is on, each end of the bar is gripped between a pair of flat metal jaws. A spring pulls the bar the other way, toward two stops. The handle turns a disc that lies over the bar, and under the disc is a ward, which in one of Holmes’s versions is a pair of pins. It can turn about 30° before it meets the bar.

Before you turn the handle back in Fig. 2, guess how far it goes before the bar moves.

Holmes’s quick-break switch seen from above, switched onhandlespringstopjawsbar
Fig. 2 Holmes’s switch from above, switched on, drawn after Fig. 2 of his US Patent 305,310 (1884). The two pins of the ward lie under the disc, so they are dashed, and so is the bar where the disc covers it. Watch the pins and the bar. Not to scale.
What the drawing shows
Holmes’s switch from above. Inside a round box, a long contact bar swings about the centre. Its two ends sit between pairs of flat jaws, which hold it while the switch is on. A spring runs from a post to the bar and pulls it back toward two stops. Over the middle of the bar lies a disc with the handle on top, and under the disc two dashed pins turn with the handle, one on each side of the bar. Turning the handle back, the bar stays put until a pin reaches it, then moves with the pin until it leaves the jaws and jumps to the stops.

For the first 30°, only the handle moves. Then a pin meets the bar and pushes it along at the speed of your hand, until the bar slips out of the jaws. At that instant the spring throws it back to the stops. However slowly the handle is turned, the bar leaves the jaws too fast for a dangerous arc to form. Turning the switch on was slower. The other pin pushes the bar back between the jaws against the spring, as fast as you turn.

From toggle to rocker

The toggle came later. William J. Newton of Lynbrook, New York, applied for a patent on a flush switch in May 1915 and was granted US patent 1,233,597 in July 1917. Until then, he wrote, flush switches such as his own had been worked by two buttons through the plate. He wanted a small switch with one pivoted lever, which he also calls a toggle or tumbler, and a quick make and quick break, as the National Board of Fire Underwriters required. Wikipedia dates the toggle switch to 1916 and gives Morris Goldberg as Newton’s co-inventor. The patent names Newton alone.

In the United States, Canada and Finland, a toggle is usually up for on. In the UK, Ireland and much of Europe, on is down, and many switches there are rockers, a broad flat lever that sits almost flush with the plate. An Australian rocker has the parts of Fig. 1 in another shape. A compression spring presses a bar into a notch in a rocking contact bar and stores energy until the rocker passes its middle.

A loud click is not always a fault. Someone on DIY Stack Exchange asked how to quieten a switch, and another user answered that a quieter switch would do it, but warned that some are loud because they are made to switch heavy currents.

One lamp, two switches

A lamp over a stair can have a switch at the top and another at the bottom. A reader once asked the explainlikeimfive forum on Reddit how that works. In their house, they wrote, the light was on with one switch on and the other off, and off with both on or both off.

Each of the pair is a two-way switch in British terms, or a three-way switch in American ones. Its bar has a contact on each side, as if the stop in Fig. 1 were a second contact, and always touches one or the other. So the switch sends the current down one of two paths, and two paths join the pair. Before you flip anything in Fig. 3, guess how many of the four ways of setting the pair light the lamp.

Two stair switches and one lamp, joined by two pathsbottom switchtop switchlamptwo pathssupply
Fig. 3 The idea of two stair switches and one lamp, drawn as a diagram with none of the real wiring. Each lever touches one of the two paths. Rays round the lamp mean it is lit.
What the drawing shows
This is a diagram of the idea only. From the supply on the left, the current reaches the bottom switch. That switch’s lever touches one of two contacts, an upper and a lower, and from each contact a path runs across to the top switch, which has the same two contacts. The top switch’s lever touches one of them and leads on to the lamp, and from the lamp the loop runs back to the supply. The lamp lights, shown by short rays, only when both levers touch the same path.

Two of the four light it, and flipping either switch always changes the lamp, whatever the other is set to. A third place needs a different switch in the middle, one that crosses the two paths over.

What the drawings leave out

The sizes are the drawing’s own. Fig. 1 is not one maker’s switch. It puts the Australian rocker’s spring and rocking bar behind a toggle. Newton’s 1917 switch used a lever, a spring holder and a U-shaped yoke carrying the contact blades, and the yoke made a quarter turn when the spring passed over.

Fig. 2 takes one angle from Holmes, the 30° his ward turns before it meets the bar. The rest of it is drawn to look right.

Real wall switches carry mains electricity. Search suggestions show people asking why a switch buzzes, feels warm or gives them a shock, and one DIY Stack Exchange user asked about a switch that felt warm and sparked. Buzzing is one of the warning signs of a fault. A switch that is unusually warm, hot to the touch or gives even a mild shock should not be used until a qualified electrician has checked it.

Sources

Read in November 2026.

  1. J. H. Holmes, US Patent 305,310, “Electric-circuit closer”, 16 September 1884, for the slow arc, the spring, the jaws, the stops and the ward with its 30° of play. Fig. 2 follows its plan view.
  2. W. J. Newton, US Patent 1,233,597, “Flush switch”, applied for on 6 May 1915 and granted on 17 July 1917, for the toggle, its spring and yoke, the two-button switches before it and the Underwriters’ rule.
  3. Wikipedia, “Light switch”, on over-centre toggles, early switches, Newton’s date, which way is on and rockers.
  4. Wikipedia, “Switch”, on arcs, quick-moving contacts and the word toggle; “John Henry Holmes”, on his firm; “Multiway switching”, on stair switches.
  5. US Consumer Product Safety Commission, “Guide to Home Wiring Hazards” (Publication 518) and “Home Electrical Safety Checklist” (Publication 513, 2008), for the warning signs.
  6. r/explainlikeimfive, “ELI5 - How does a light with two switches work? …”, July 2020, via the Arctic Shift archive. User report.
  7. DIY Stack Exchange, “How can I soften the clicking sound of a light switch”, June 2016, with the answer by Harper. User report.
  8. DIY Stack Exchange, “What should I do about a switch that feels warm and arcs when toggled?”, March 2015. User report.
  9. Google’s suggestions for “why does my light switch”, fetched 15 November 2026, are user reports.

The type is Playpen Sans by TypeTogether, under the SIL Open Font License 1.1.