Office chair
Under the seat of an office chair stands a sealed tube of gas that pushes the seat upward all the time. The lever beside the seat works one small valve inside that tube. While you hold the lever up the seat can move, and once you let go it stays where it is, with you on it.
Under the seat
The post between the seat and the base is a gas spring standing in a guide tube. Both ends fit by tapers, with the guide tube in the base and the gas spring in the seat carrier. The gas spring’s rod points down. Its foot is clipped into the floor of the guide tube, on a ball bearing that lets the seat turn, and the rest slides up and down in the guide tube with the seat.
A rubber cushion between the spring and that bearing makes a soft stop at the lowest seat. Stabilus’s standard chair springs are 320 to 700 mm long when extended, with strokes of 90 to 265 mm.
The gas spring itself is a closed tube. Inside are a piston on that rod, nitrogen under pressure and a little oil for the seals. Some owners call it hydraulic. One reply on Reddit called it “a hydraulic piston” that “acts a bit springy”, and the owner of another chair, asked what kind it was, answered “A hydraulic chair”. The makers describe gas. SUSPA calls its locking springs hydropneumatic, and says that the ones which lock with some give hold only nitrogen.
The push comes from the rod. Gas presses down on the top face of the piston and up on its bottom face, but the rod covers part of the bottom face, so the two pushes do not cancel. What is left over, the gas pressure times the area of the rod’s cross-section, drives the rod out and lifts the tube with the seat. Stabilus’s springs for swivel chairs push with 300 to 400 newtons, on a rod 10 mm across. So the gas inside is about 38 to 51 bar above the air outside, even with the seat at the top.
Pulling the lever
A gas spring for a chair has two tubes, one inside the other, with a narrow ring-shaped gap between them. The firm of Fritz Bauer drew it this way in a patent of 1989, which these drawings follow. The piston slides in the inner tube and splits it into a space above the piston and a space below, round the rod. At the bottom, the space below opens into the gap. At the top, the valve sits between the gap and the space above, and its pin sticks out of the tube under the end of the lever.
Lifting the lever presses the pin in. In the drawing the lever’s knob is ten times as far from its pivot as the end on the pin, so the 90 to 120 N that a chair spring’s pin needs takes 9 to 12 N at the knob. With the pin in far enough, the valve opens and gas can pass between the two spaces by way of the gap. Both faces of the piston then feel one pressure again, and the seat moves wherever the push and your weight send it. Fig. 1 starts with nobody on the seat. Before you lift the lever, guess which way the seat will go.
What the drawing shows
With nobody on it, the seat rises to its top stop, driven by the gas. Choose to sit, pull again, and it sinks, because your weight is more than the push. The drawing’s seat sinks more slowly than it rises, at speeds of its own.
The pin and its two seals
The valve itself is in Fig. 2, drawn larger from the description in Bauer’s patent. The pin runs down through the valve body with a ring seal round it near the top and a second one lower down. The upper seal stops gas leaving along the pin. The lower one shuts off the space above the piston. Between the two seals the pin is thinner, a waist, and the room round the waist has a channel out to the gap. A plate on the pin’s inner end keeps it from being pushed out of the valve. Before you press, guess how far the pin must go in before gas can get by.
What the drawing shows
It takes 1.6 mm in the drawing. Until then the lower seal still grips the full width of the pin. Past that, the waist reaches below the seal, and gas can slip round the pin between the space above the piston and the channel, in either direction. Stabilus’s standard valve opens within 2.5 mm of travel. Let go, and the gas pressing on the end of the pin pushes it back out, so the full width comes back into the lower seal and the valve shuts by itself.
A little give
With the valve shut, the gas above the piston cannot get below it. When you sit down, the seat squeezes that gas until it pushes back as hard as you press, so the seat gives a few millimetres and stops. In Fig. 1, leave the lever alone and choose You. The drawing’s seat gives 9.3 mm under 550 N, the weight of about 56 kg, and rises the same amount when you get up. Stabilus sells the give of its chair springs as a comfort, and SUSPA’s locking springs that hold only nitrogen give in the same way.
With the seat low in its travel, the space above the piston is short, and the locked spring then gives only a little. The drawing’s seat gives 3.6 mm there. One Humanscale owner asked on Reddit whether a seat that sank 5 to 10 mm each time they sat, and rose again when they stood, was normal. The replies said yes, as long as it did not keep sinking.
When the lever holds the pin in
For the seat to keep sinking under you, gas has to get from the squeezed space above the piston to the space below. The lever itself can let it through. Many chairs pressed from the top have a set screw that decides how far the lever presses the pin. Set too tight, it holds the valve open, and the chair rises on its own when empty and sinks when someone sits. A little too tight, it does both more slowly. The lock is safe only when there is little play between the release parts and the pin, and Stabilus sells pins that can be set with a screw. In Fig. 1 the valve opens once the lever is up about 6°, short of its full 10°.
Owners on Reddit describe both. One new chair sank to its lowest whenever its owner sat, and rose to the top when they got up; a reply blamed a wrongly set screw. Another owner fitted a replacement cylinder with a taller button, and the chair’s frame kept that button pressed even with the screw taken out, so the seat rose and fell by itself.
Seats that creep down
The other way is a worn seal. The drawing treats a seal that leaks between the two spaces as a valve that never quite shuts. While you sit, the gas above the piston is under more pressure than the gas below, so some seeps past and the seat slowly sinks. Before you move through the day in Fig. 3, guess whether a cylinder with sound seals lets the seat move at all after you sit.
What the drawing shows
The sound seat moves once, by its few millimetres as you sit, and then stays at 56 mm all day. With the drawing’s worn seal it creeps down 28 mm in eight hours, and with the pin held in a little it reaches its rubber stop in 21 minutes.
Owners report the slow kind too. In one thread an owner wrote that their chair had a leak and lowered over time, and the owner of a chair assembled that same day found it going down a few hours later. Another said theirs leaked faster when they leaned one way, and sideways loads do wear gas springs early. Gas can also leak out past the seal round the rod, and then the push itself grows weaker; one user said of chairs kept too long that “the spring force goes down”. Stabilus’s gas springs in general lose less than 8% of their push in the first two years. Whatever the seat’s height, the tube stays full of gas under pressure, and a gas spring must never be heated, damaged or altered.
Fritz Bauer’s tubes
Stabilus says it was the first company to make gas springs in large numbers, in the early 1960s, and that car doors and swivel chairs were their first big uses. Fritz Bauer filed a US patent in 1969, granted in 1972, for a lifting device with a double tube and a passage between the tubes, blocked at one end until the height is to be changed. A year later he filed one, granted in 1973, for a chair whose gas spring forms part of the column, with its rod pointing down into a guide tube. The 1989 patent from his firm names both as the designs it improves.
That patent also says how a seat is meant to be raised and lowered. You lower it by sitting on it with the valve open, and raise it by taking your weight off, which the patent calls a “cramped position”. Its valve lets the seat fall more slowly than it rises, so you can stop it at the height you want and spend only a moment half standing.
What the drawings leave out
The sizes are the drawing’s own. The tubes are drawn wider than real ones, so that the gap between them shows, and the valve in Fig. 2 is drawn about ten times life size. The lever’s reach, the seat’s speeds and the rates at which it creeps come from the drawing’s model too, since no maker gives a rate of creep.
Nothing in them shows the seal round the piston, the ribs that hold the inner tube or the damping passages, and they ignore the weight of the seat. The gas appears only as arrows, and the oil as a line where it lies over the seal round the rod.
Two sizes come from a real spring, the rod 10 mm across and the pin standing out 6.5 mm. The drawing’s push, 320 N at the top and 359 N at the bottom, lies inside the 300 to 400 N that a chair spring usually gives.
Sources
Read in November 2026.
- H.-P. Bauer, H. J. Bauer and A. Gebhardt, US Patent 4,844,392, “Gas spring adjustable in length for vertically adjustable chairs, tables and the like”, 4 July 1989, for the chair gas spring, its two tubes, valve, pin and seals. Fig. 2 is drawn from its text; its drawings are not shown.
- F. Bauer, US Patent 3,656,593, “Continuously adjustable lifting devices”, 18 April 1972, for the lifting device with a double tube.
- F. Bauer, US Patent 3,711,054, “Continuously adjustable lifting devices”, 16 January 1973, for the gas spring as a chair’s column.
- Stabilus, “Gas springs: technical information” (2002), in a copy kept by an RV parts seller, for the push, the chair springs, their valves and their give.
- Stabilus, “STAB-O-MAT & STAB-O-BLOC: lockable gas springs”, “BLOC-O-LIFT and KOMBI-LIFT” and “Service gas springs”.
- SUSPA, “Lockable gas springs”.
- Crandall Office Furniture, “Adjusting your gas cylinder set screw”, for the set screw over the pin.
- r/explainlikeimfive, “ELI5: How is it possible that office chair cylinders don’t leak?”, March 2024, via the Arctic Shift archive. User report.
- r/explainlikeimfive, “ELI5: How does the height adjustment work on an office chair?”, December 2014, via the Arctic Shift archive. User report.
- r/OfficeChairs, “Humanscale Liberty - occasionally sinking 1cm when I sit, rises 1cm when I get up”, May 2024, via the Arctic Shift archive. User report.
- r/OfficeChairs, “I got an office chair but it’s sinking down when I sit on it and it’s getting back up when I get off from it”, March 2023, via the Arctic Shift archive. User report.
- r/OfficeChairs, a thread on a Steelcase Leap whose frame kept a new cylinder’s button pressed, August 2020, via the Arctic Shift archive. User report.
- r/OfficeChairs, “Brand new office chair assembled today is slowly sinking”, October 2024, via the Arctic Shift archive. User report.
The type is Playpen Sans by TypeTogether, under the SIL Open Font License 1.1.