Howthings

Seat belt

In a car, the seat belt winds onto a reel with a spring inside that keeps pulling the belt back in. Lean forward slowly and the reel lets the belt out after you. Lean too quickly, or brake hard, and a pawl swings into teeth on the reel and holds the belt where it is.

One pawl for two catches

The belt winds on a shaft that a spring turns toward winding, and a ratchet wheel is fixed to the same shaft. A single pawl hangs beside the wheel, held out of its teeth by its own weight. Once the pawl is in the teeth, the shaft cannot turn the way the belt comes out. In the reel drawn here the pawl has two catches, and each can push it in on its own. A car can leave the road and roll over with no sudden pull on the belt like a collision’s.

The drawings on this page follow one design. Robert L. Stephenson filed it for Allied Chemical in 1973, and it became US Patent 3,858,824 in 1975. The US safety standard for seat belts, FMVSS 209, calls the reel a retractor. The kind that locks in an emergency is an emergency-locking retractor, and the standard lets three things set off its lock: the car’s acceleration, the belt moving relative to the car, or some other automatic action. On a belt made since 22 February 2007 that crosses both chest and lap, the reel’s spring must pull the belt back with at least 1 and at most 7 newtons. These are the US tests for new belts, not a rule for every country.

A wheel that lags behind

The first catch feels the belt. A spur gear on the shaft drives a small pinion on a heavy wheel, so pulling the belt out spins the wheel the other way, and faster than the reel. For car belts Stephenson preferred a gear two to three times the size of the pinion. The heavy wheel turns on a plate that can itself swing about the shaft, and a light spring holds the plate against a stop pin.

Draw the belt out gently and the wheel keeps up. Snatch it, and the wheel lags. Its own inertia holds it back. The gear then shoves on the lagging pinion, and the shove swings the whole plate round the shaft against its spring. An arm on the plate pushes a pin on the pawl, so the pawl swings in among the teeth. The arm can push but not pull. When the belt goes slack, the pawl falls back by its own weight.

For a reel that senses the belt, FMVSS 209 sets two limits. Pulled at 0.3 g or less, it must not lock before 51 mm of belt has come out. At 0.7 g every emergency-locking reel must lock within 25 mm. Fig. 1 draws Stephenson’s catch with a heavy wheel of 8 g and a spring that lets the plate move from 0.2 g. Before you pull its belt at 0.7 g, guess how much of it comes out before the reel stops.

A seat belt reel seen end on, with its pawl and the catch for the beltbeltpawlteethplateheavy wheelspring
Fig. 1 The reel seen end on, with the brass belt running up off its left side and the plate’s heavy wheel in front. The heavy wheel lags only while the belt is gaining speed. Stephenson’s design, drawn from his patent’s words. Not to scale.
What the drawing shows
The reel seen end on. Belt is wound on it in a grey coil and runs off its left side, brass, up toward the shoulder. Behind the belt is a ratchet wheel with eighteen teeth. Below and left, a pawl hangs on a pivot, resting on a pin with its tip clear of the teeth. In front, a plate turns on the shaft, held on a stop by a spring on the right. It carries a heavy wheel whose small pinion meshes with a gear on the shaft. The plate’s arm reaches down to a pin on the pawl. A sharp pull swings the plate and pushes the pawl into the teeth.

The reel stops after 6.3 mm. That is a quarter of the 25 mm the US test allows. The pawl is among the teeth almost as soon as the pull starts, and the belt comes on only until the next tooth reaches it. At 0.3 g the plate swings 4°, yet the pawl’s tip stays 1.9 mm outside the teeth and the belt runs on. Because the drawing’s wheel lags only while the belt gains speed, a belt drawn out at a steady pace leaves the plate on its stop, however fast it runs.

A weight on a collar

Stephenson’s second catch feels the car. He hung a weight on a rigid rod with a button-shaped disc on top. The rod passes through a hole in a plate, and the disc rests on a raised collar round the hole. An arm pivoted on the frame lies across the disc, with a small nodule under it sitting in a dip at the disc’s middle. Its far end reaches the pawl.

When the car brakes hard or hits something, the weight swings toward the point of impact, whether front, back or side. The disc rocks up on the collar and lifts the arm, and the arm lifts the pawl into the teeth. In the drawing, gentle stops move nothing. In Fig. 2 the collar’s edge is 3.6 mm from the middle and the weight hangs 15 mm below it, so the push on the weight must reach 3.6 parts in 15 of its weight, 0.24 g, before the disc will tip at all. Before you brake in Fig. 2, guess what braking brings the pawl to the teeth.

The lower part of the reel, its pawl, the arm under it, and the weight on its collarteethpawlarmcollarweight
Fig. 2 The lower part of the reel, with the brass weight hanging under its collar. The car faces right, so braking swings the weight forward and rocks the disc on the back edge of its collar. The collar and its plate are drawn cut through the middle. Not to scale.
What the drawing shows
The lower part of the reel, its teeth along the bottom, cut off above by a wavy line. The pawl hangs below the teeth on a pivot at the left. Under it, a long arm is pivoted at the right; a finger on its left end touches the pawl’s underside, and a nodule under its middle rests on a disc. The disc sits on a raised collar round a hole in a plate, and a rod hangs from it through the hole to a brass weight. Braking swings the weight forward, tips the disc, raises the arm and pushes the pawl up into the teeth.

In this drawing the pawl reaches the teeth at 0.40 g of braking. At 0.30 g the disc has rocked 3° and the pawl’s tip is still 1.9 mm out. From 0.42 g nothing moves any further, because the pawl has reached the bottom of the teeth and holds the arm down on the disc. FMVSS 209 holds this kind of reel to the same test as the other, a lock within 25 mm of belt at 0.7 g.

Parked on a hill

To the weight, a tilt and a push feel alike. Tip the reel, and gravity pulls the weight toward the downhill side as a push would. For a reel that senses the car, FMVSS 209 says it must not lock when turned 15° or less in any direction from the way it is mounted. It must lock once tilted more than 45°, unless it passes the acceleration tests turned to 45°, 90°, 135° and 180°. Stephenson’s patent sets the arm’s gap below the pawl so that it acts only at a greater lean than a sloping road gives, to tell a roll-over from “undesirable locking on a steep hill”. Before you tilt Fig. 3, guess how steep a slope locks its belt.

The same reel and weight, tilted with the car on a slopepawlweightcar floorplumb line
Fig. 3 The reel and weight of Fig. 2, with the car standing nose down on a slope. The dashed plumb line hangs straight down from the uphill edge of the collar. Not to scale.
What the drawing shows
The reel, pawl, arm, collar and weight of Fig. 2, with the car’s floor drawn as a line beneath them. Making the slope steeper tilts all of it, floor and reel together, clockwise. The weight leans with the reel at first. Past about 13°, the disc begins to rock on the uphill edge of its collar, and the weight hangs on, almost straight down, while the reel tilts further. A dashed vertical line from that edge shows straight down. As the disc rocks, it lifts the arm and pushes the pawl toward the teeth.

The pawl reaches the teeth on a slope of 21.7°, the same lean that 0.40 g of braking gives the weight, because the tangent of 21.7° is 0.40. A slope that steep rises 40 cm in every metre; one of 15° rises 27 cm. Once the disc rocks, the weight’s middle hangs on the plumb line, straight below the uphill edge of the collar. Past 22.7° the arm, held up by the pawl, stops the disc rocking further.

When it locks with nobody pulling

A slow, easy lean draws the belt out with you, and a lean that is too quick locks it, as a sudden stop or a collision does. A reader on r/explainlikeimfive, in a user report, asked how a belt tells a fast pull from a slow one. The top answer described another kind, with two grips inside the spindle that are thrown outward when it spins quickly. Neither that answer nor Stephenson’s patent says which kind is more common.

Other readers in that thread asked, in further user reports, why a belt locks when nobody pulls it. One reply asked why the belt holds them tight while they stop slowly at a stop sign. Another answered that a second part responds to heavy slowing. A third suggested that a movement of the body or a deep breath, with the stop, is quicker than it feels. Figs. 1 and 2 show both causes. A quick lean is a sharp pull on the belt, and a stop harder than 0.40 g locks the drawing’s reel with no pull at all. Fig. 3 adds a slope.

Someone asked on Motor Vehicle Maintenance & Repair Stack Exchange, in another user report, why the rear belts of a 2004 Toyota Corolla Runx lock, and only wind back in once let all the way back. The accepted answer called it a feature for holding a child seat. Hyundai’s manual describes the same mode for its rear belts. Pulled all the way out, the belt will wind in but not out until it is unbuckled and let back fully. Hyundai’s pretensioner pulls the belt tighter in certain frontal or side collisions, and only an authorized Hyundai dealer should inspect, repair or replace it.

Belts before reels

Edward J. Claghorn, of New York, was granted a patent for a “safety-belt” in 1885. It had nothing to do with cars. It went round the waist, with hooks and straps to fasten the wearer to a fixed object and to let them down from a height, and he named tourists, sailors, painters, farmers, firemen and telegraph-men as its users.

Nils Ivar Bohlin’s patent for Volvo, filed in the US in 1959 and granted in 1962, joins a chest strap and a hip strap into one sling. It runs from a mounting behind the shoulder, off to one side, down to floor mountings on both sides of the seat. Volvo says it was the first maker to fit three-point belts as standard, in 1959, and that it then let every car maker use the patent free.

Bohlin’s patent let the chest strap pass over a shoulder or under the arm. NHTSA says never under an arm or behind the back. The lap belt goes across the hips, not the stomach, and the shoulder belt across the middle of the chest, away from the neck.

What the drawings leave out

The sizes are the drawing’s own. The parts are drawn in one plane, though Stephenson’s ratchet wheel sits at the reel’s other end and his catches outside the near wall. The two catches are drawn apart, each shown with the pawl they share.

No friction is drawn. Nor are the weights of the pawl, arm, plate and disc, or the pull of the reel’s spring. Each catch is worked out for a push that holds steady, while a real plate or weight takes time to move; the US test allows for that by measuring how much belt comes out before the lock. The shapes of the teeth, the pawl and the arm are this page’s own, made from his words, and so are the places of the pins the pawl and the plate rest against. The patent gives one number, a gear two to three times the size of its pinion, and the drawing’s gear is 2.5 times.

Sources

Read in November 2026.

  1. US National Highway Traffic Safety Administration, 49 CFR 571.209, Standard No. 209, “Seat belt assemblies”: S3 and S4.3(j) for the reel’s limits, S5.2(j) for its tests.
  2. R. L. Stephenson, US Patent 3,858,824, “Dual action safety seat belt retractor”, 7 January 1975: the design all three drawings follow, from its text.
  3. E. J. Claghorn, US Patent 312,085, “Safety-belt”, 10 February 1885.
  4. N. I. Bohlin, US Patent 3,043,625, “Safety belt”, 10 July 1962, from its text.
  5. Volvo Car UK, “Volvo celebrates 70 years of the seatbelt”, 2026, the maker’s own account.
  6. NHTSA, “Seat Belts”, for how a belt should sit.
  7. Hyundai, owner’s manual page “Seat Belt Restraint System”, 2025.
  8. r/explainlikeimfive, “ELI5: How does the seatbelt know that it’s being pulled fast (crash) and stop extending but still extends when pulled slowly?”, October 2018, via the Arctic Shift archive. User report.
  9. Motor Vehicle Maintenance & Repair Stack Exchange, “What is the purpose of seatbelts only retracting when extended past a certain point?”, October 2017, and the answer marked accepted. User report.

The type is Playpen Sans by TypeTogether, under the SIL Open Font License 1.1.