Howthings

Soap pump

Liquid soap leaves a pump bottle in a squirt each time you press the head, and as the head springs back up, the next squirt is drawn up a thin tube from the bottom of the bottle. Inside the pump, two small balls rest on two holes and let the soap pass one way only.

Under the head

The pump hangs in the neck of the bottle. At the top is the head, the part you press, with the nozzle sticking out of one side. The head sits on a hollow stem, which runs down through the collar, the threaded cap that screws onto the neck. Below the collar the stem goes into a plastic cylinder, and on its lower end is the piston, a disc that fills the cylinder’s bore. The dip tube hangs from the foot of the cylinder and reaches down into the soap.

Pumps differ inside. The one drawn here is a typical kind, with its spring standing in the cylinder under the piston, in the soap. It has two balls. The lower ball rests on a hole in the foot of the cylinder, where the dip tube joins it. The upper ball rests on a hole through the piston, at the foot of the stem. A ball sitting on its hole closes it. Lifted off, it lets soap by.

Fig. 1 starts with a pump that has been used before, so its cylinder is already full of soap. Before you press the head, guess which ball will move.

A soap pump cut open down its middle, in the neck of its bottleheadupper ballspringcylinderlower balldip tube
Fig. 1 The pump cut open down its middle in the neck of the bottle. Watch the two balls, and the arrows that show which way the soap is moving. Not to scale.
What the drawing shows
A tall cut through the pump in the neck of a bottle. At the top is the head, with the nozzle pointing right. A hollow stem runs down from it through the collar into the cylinder and ends in the piston. A small ball sits on the hole in the piston, and a zigzag spring stands under the piston. At the foot of the cylinder a second ball sits on a hole above the dip tube. Pressing moves the head, stem and piston down, squeezes the spring and lifts the upper ball, and a drop grows at the nozzle. Letting go lifts the lower ball instead.

The upper ball lifts, and the lower one stays put. The piston squeezes the soap under it, which presses the lower ball harder onto its hole, so the soap cannot go back down the tube. Its only way out is up through the piston. The soap lifts the upper ball, runs up the hollow stem and leaves by the nozzle.

Letting go

When you let go, the spring pushes the piston and the head back up. The upper ball drops onto its hole, so nothing can come back down the stem. The space under the rising piston grows, and a vacuum forms there. That lifts the lower ball, and soap comes up the dip tube to fill the cylinder for the next press.

The dose depends on the cylinder’s bore and on how far the head goes down. In the drawing the bore is 13 mm across and the head travels 15 mm, so one full press sweeps 2 mL. Both sizes were picked for the drawing, to match a pump that one supplier lists at 2 mL a press. Another supplier’s guide gives 2 to 4 mL for a standard pump on hand soap, and 0.5 to 1.2 mL for a small one. A press stopped partway gives that share of the dose.

Most pumps have a metal spring. A steel one can rust into the product and makes the pump hard to recycle, so a patent of 2022 gives its pump a plastic spring around the piston, between the collar and the head.

Taking a ball out

The two balls do different jobs, and Fig. 2, the cylinder alone and drawn larger, lets you take either one out. Before you press, guess which ball the pump could do without.

The pump’s cylinder cut open, larger, with its piston, spring and two ballsupper ballpistonspringlower balldip tube
Fig. 2 The cylinder from Fig. 1, larger, with its stem broken off at the top. Watch the arrows for where the soap or the air goes, with both balls in or one taken out. Not to scale.
What the drawing shows
The cylinder cut open down its middle, with the collar at the top and the start of the dip tube at the bottom. The hollow stem comes down through the collar and ends in the piston, with the upper ball on the hole through it. The spring stands under the piston, and the lower ball sits on the hole at the foot. Taking a ball out removes it from the drawing. Arrows show where soap or air is moving: up or down the stem, and up or down the dip tube.

It needs both. With the lower ball gone, nothing closes the foot of the cylinder, so the press pushes the soap back down the tube into the bottle, the way it came. In the drawing none of it reaches the nozzle, and letting go draws it up again.

With the upper ball gone, the first press still works, because the lower ball holds. Letting go is where it fails. Only a closed upper ball lets a vacuum form under the rising piston and lift the lower ball. Without it the piston draws on the open stem, and air comes in through the nozzle. The next press pushes out that air.

A bottle with this pump also leaks when it is not upright. On its side, both balls roll off their holes and the lotion runs freely out of the nozzle.

When no soap comes

A new pump is full of air. Its first few presses bring no soap. Press the head all the way down, let it come all the way up, and repeat until soap appears. A thick soap takes more strokes, and a very thick cream may not refill the cylinder fast enough. If soap never comes, the collar may not be screwed down tight, the dip tube may not reach the soap or may be kinked, or the soap may be too thick for the pump.

Often the head is locked. Many pumps are shipped pressed down and turned, so that a short thread under the head holds it in the collar; turned back, it springs up. On Reddit’s r/NoStupidQuestions, people asking why a pump bottle would not work have been told to twist it. One shampoo head came up only after its owner turned it hard to the right and then to the left. These are users’ reports.

In a thread on r/explainlikeimfive that asked why the tube stops short, the top-voted answer, a user report, said that a tube touching the bottom would suck itself onto it. Other users said the thin tubes bend or warp over time, and one writer’s lotion bottles left about an inch of space under the tube.

The dip tube is cut short on purpose, about an eighth to a quarter of an inch (3.2 to 6.4 mm) shorter than the inside of the bottle. Too long, it bends or kinks against the bottom, the pump may not screw down fully, and it can draw air. Too short, it stops drawing while soap is still left (Fig. 3).

The foot of a dip tube in three bottles: too short, about right and too longdip tubesoap5 mmtoo shortabout righttoo long
Fig. 3 The foot of the dip tube in three bottles, seen from the side. On the left the tube ends too high and leaves soap under it. In the middle it stops 5 mm above the bottom, and on the right it is too long and bends. Not to scale.

Soap first, then the pump

Liquid soap is older than the pump bottle. William Sheppard of New York patented it on 22 August 1865. He dissolved about a pound of common soap in a hundred pounds of ammonia, which thickened it to the consistency of molasses. His patent is for the soap and says nothing about a pump.

Pumps that sit in a bottle are older too. Anthony Peron’s patent of 1918 is for one that stood in a bottle of table water, with a valve at the foot of its barrel, a hollow piston with a valve of its own, and a spring under the piston. It worked the other way round from a soap pump: pressing let the water through the piston, and the spring’s push upward sent a tumblerful out of the spout. Its rod could be pushed down and turned to lock it.

The first liquid soap sold widely in a plastic pump bottle was Softsoap, in 1980. Robert R. Taylor’s Minnetonka Corporation was small, and soap in a pump bottle was easy to copy. Two business professors later wrote that pumps “had been around since Archimedes”. So Taylor secretly ordered 100 million of the small plastic pumps then used for lotions, which the Los Angeles Times says tied up a full year’s output of the only makers. The Independent names one maker, Calmar, where Wikipedia counts two. Taylor sold Softsoap to Colgate-Palmolive in 1987 for $61 million.

What the drawings leave out

The sizes are the drawing’s own. Both pump drawings leave out the seals round the piston and under the collar, the thread inside the collar and the lock under the head. Their balls lift further than real ones would, so that you can see them move, and the soap shows only as arrows and a drop. The spring is one zigzag line from the piston down to the shoulder. In Fig. 1 the bottle’s neck is cut off just below the collar and the dip tube a little way down, and Fig. 2 breaks the stem off above the collar.

Only the dose matches a real pump. The bore and the stroke were picked so that one full press sweeps 2 mL, the dose one supplier lists for its pump, and every other part was drawn to fit them. The pump drawn is also one design of several. Others put the spring outside the cylinder, so that no metal touches the soap, or make the spring of plastic.

Sources

Read in November 2026.

  1. F. Kuo, US Patent 4,930,670, “Pumping mechanism for dispensing lotion in bottle/container”, 5 June 1990, for its account of a typical pump, the two balls and the lock for transport. Text only; its drawings are not shown.
  2. M. S. Carter, US Patent 5,335,830, “Pump dispenser for lotions and/or large doses of product”, 9 August 1994: a lotion pump with its spring outside, and shipping locked down.
  3. A. Arminak, US Patent 11,389,814, “All plastic hand pump with a piston having an integrated check valve”, 19 July 2022, and why steel springs are a problem.
  4. Citadel Packaging, a guide to lotion pumps: parts, doses, locks, priming and dip tube length.
  5. Berlin Packaging, a 2 cc pump for 24-410 bottles.
  6. W. Sheppard, US Patent 49,561, “Improved liquid soap”, 22 August 1865.
  7. A. Peron, US Patent 1,264,554, “Device for dispensing liquids”, 30 April 1918: his pump for table water.
  8. S. Chawkins, Los Angeles Times, 12 September 2013: Robert R. Taylor’s obituary.
  9. R. Marsden, The Independent, August 2015: a short history of the liquid soap dispenser.
  10. Wikipedia, “Soap dispenser” and “Softsoap”.
  11. r/explainlikeimfive, “ELI5: Why do manufacturers of products that use pump dispensers (lotion, soap, etc.) not make the tube reach the bottom?”, February 2021, via the Arctic Shift archive. User report.
  12. r/NoStupidQuestions, “I can’t get my pump bottle to work?”, November 2020, via the Arctic Shift archive. User report.
  13. r/NoStupidQuestions, “Lotion bottle won’t pump out”, February 2021, via the Arctic Shift archive. User report.
  14. r/NoStupidQuestions, “How do I get this shampoo bottle to pump?”, November 2022, via the Arctic Shift archive. User report.
  15. Lifehacks Stack Exchange, “How can I lock the pump of a JASON soap pump bottle?”, February 2019, with the answer by Lawrence. User report.

The type is Playpen Sans by TypeTogether, under the SIL Open Font License 1.1.