Tap
Pipes below a tap hold their water under pressure, and it flows as soon as anything inside the tap lets it past. In an older screw-down tap, turning the handle lifts a rubber washer off a ring. In a quarter-turn tap, the handle slides one ceramic disc across another.
A washer on a seat
Water comes up a screw-down tap’s supply pipe to a ring with a hole through it, the seat. The seat stays put. Above it hangs a short head with an elastic washer on its lower face. The head belongs to a thick plug with a thread round it, and the plug turns in a matching thread inside the body. A stem rises from the plug, through the cap, to the handle.
American readers call the tap a faucet. Fig. 1 is drawn after one that Morgan S. Byrne Jr. of Staunton, Virginia, patented in 1898, of the kind that closes by compression. Turning the handle turns the plug, and the thread carries it up or down. Screwed down, the plug presses the washer onto the seat and the hole is shut. Screwed up, it lifts the washer clear, and water runs between the two, round the head and out of the spout. By 1909 it was customary for a compression faucet to close when its handle turned clockwise, and the drawing’s thread works that way.
The hole through the drawing’s seat is 12 mm across. Before you turn the handle in Fig. 1, guess how high the washer must rise before the gap round its edge is as large as the hole.
What the drawing shows
The washer needs to rise only 3 mm, a quarter of the hole’s width. Water leaving the hole passes through a short ring-shaped wall of space between washer and seat, as tall as the lift and as long as the hole’s edge, which is 37.7 mm round. At 3 mm that wall has the hole’s own area, 113 square millimetres. The drawing’s thread climbs 1.5 mm a turn. Two turns get there. Turning further makes the gap larger than the hole without making the way through any wider.
Real taps differ. One DIY guide gives at least two and a half turns from off to full on for washer taps, and a forum user wrote of turning old taps through a full 360 degrees or more.
Why the washer wears
When the handle closes the tap, the washer turns while it presses on the seat. That rubbing wears the rubber down or cuts it until its face is no longer even. Sand caught between washer and seat sinks into the rubber and scratches the seat, and water in many places corrodes a brass seat as well. Wherever a nick or a ridge leaves a path, the shut tap leaks.
A drip also grows. Water forced at speed through a small nick in the seat wears the nick larger, which is known as wire-drawing of the seat, and then the handle needs still more force to stop the drip. People used to leaky taps shut them with many times the force needed. That wears washer and seat faster. In Fig. 1, choose the worn washer and shut the tap to see the path its uneven face leaves.
Grit can also arrive all at once. A user on Home Improvement Stack Exchange found a tap dripping after a plumber had turned the house’s water off and on again. The accepted answer said that this often loosens crud in the pipes, and some of it may lodge in the part of the valve that seals.
Two ceramic discs
A ceramic-disc tap has no washer. A German patent published in 1983 for the firm of Otto Fluehs describes the part screwed into the tap body, its valve top, and Fig. 2 follows it. At its lower end is a disc of ceramic with openings through it. The head piece holds this disc still and presses it, through a sealing ring, onto the seat in the tap body. A second ceramic disc with openings lies on the first and turns with the spindle. With the openings lined up, water rises through both discs into a sleeve and leaves through windows in its side. Turned away, the upper disc covers the openings of the lower one.
A cross-piece on the spindle turns between stops in the head piece, which limits how far the handle goes. A tap of this kind is sold as quarter turn. One buyer asked on Stack Exchange whether a “1/4 turn” cartridge meant the handles would move only a quarter of the way round, and the answer said yes. Before you turn the top disc, guess how far it goes before any water gets through.
What the drawing shows
The top disc turns 10° first, because the drawing leaves a strip of solid disc that wide beside each opening, so the shut tap seals with some to spare. After that the open area grows in step with the angle, about half a square millimetre a degree, to 47 square millimetres at a quarter turn. One DIY guide warns that someone used to washer taps can turn a quarter-turn handle too hard and get a blast of water at full pressure.
Flat enough to seal
Two hard faces seal only if nothing gets between them. Richard G. Parkison made the discs of his 1974 faucet, for American Standard, from alumina, a ceramic that keeps its shape. They were ground and polished so flat and smooth that no liquid could pass between them, and held together with a set minimum pressure. He expected the pair to work for perhaps twenty years without any service.
A leak from a cartridge usually comes from its inlet and outlet seals failing or from sediment built up in them, and hard water wears them sooner. On a UK forum, one user passed on what a plumber had told them. Grit trapped between the two faces scores them, and the scoring can be very fine and still let water through. Tightening will not stop the drip, another user wrote, because a ceramic valve has nothing soft to squeeze. One DIY guide says the discs do wear out, and that such a tap will drip in the end.
Hot and cold from one lever
A mixer brings hot and cold water out of one spout, and a single lever can set both the mixture and the flow. Parkison’s patent of 1969 does it with two ceramic discs. The fixed disc has a hot inlet and a cold inlet side by side, and an outlet. The moving disc has a long hollow in its underside that can join either inlet, or both, to the outlet. Tilting the lever slides the moving disc along and sets the flow. Swinging it turns the disc, so the end of the hollow moves onto one inlet and off the other. His patent puts hot on the left. A disc turned a little toward cold, with the lever half up, then passes about three quarters cold and one quarter hot.
Fig. 3 is drawn from his words alone, and it starts with the lever up and in the middle. Before you swing it toward cold, guess whether the total opening stays the same.
What the drawing shows
The total hardly changes as the lever swings, because the hot opening shrinks about as fast as the cold one grows. In the drawing it stays between 17 and 19 square millimetres. A single-lever mixer joins its hot and cold sides inside, so a Stack Exchange answer warned someone who wanted to leave such a faucet’s hot pipe disconnected that cold water would run back out through it.
Hot water from a tap can scald. Most adults suffer third-degree burns after two seconds in water at 150 °F, about 66 °C. Even at 120 °F, five minutes could do it.
Drips after closing
Not every drip after a tap is shut means a worn part. On Home Improvement Stack Exchange, a user asked why a bath faucet with separate hot and cold handles, newly fitted with washers, dripped for 3 to 5 minutes after it was shut. One reply guessed that the drops were the film of water left inside the pipes running down. Another said a plumber had told them the same, and that it is normal if it stops within about 20 minutes.
Longer drips can have other causes. A third user traced a drip of many minutes to a diverter knob on the bath spout, screwed in too far, which let water from the shower head run back down. Once the knob was turned back, the drip stopped within seconds. On a UK forum, a user returned a mixer that kept water in its spout and let it out when the spout was swung.
Rotherham and Seattle
The screw-down tap is older than Byrne’s faucet, but who made it first is not settled. Wikipedia says the Rotherham brass founders Guest and Chrimes patented and made the first one in 1845. The British Film Institute’s note on a 1901 film of their works says Peter and Edward Chrimes opened a brass foundry in Rotherham’s Market Place in 1843, making high-pressure taps first, and that John Guest joined them in 1847. A Guardian article of 2000 has Edward Chrimes pioneering the screw tap in the 1820s. By 1974 the compression faucet was the conventional kind, in use for decades, and one DIY guide calls washer taps the older kind and ceramic taps the newer.
The single lever came later. Alfred M. Moen of Seattle filed a patent in 1943, granted in 1945, for a mixing faucet whose one handle set both the mixture and the flow. Swinging it sideways through a set arc took it from all cold at one end to all hot at the other, and tilting it up or down set how much came out. Inside, a piston slid and turned in a sleeve with ports for the hot and the cold.
What the drawings leave out
The sizes are the drawing’s own. So are the shapes of the disc openings and of the mixer’s hollow, and the strip of solid disc, 10° wide, beside each opening in Fig. 2.
Fig. 1 follows Byrne’s second figure in its own proportions, and leaves out the stuffing box round the stem and the elastic cushion under Byrne’s seat. Its thread is drawn as sloping lines across the plug, and they stay put while the plug turns and rises, because the turning carries the thread down the plug as fast as the thread lifts it. Parkison’s patent presses the mixer’s discs together with rubber sleeves, and the drawing leaves those out too.
Water appears only as arrows in the first drawing, and in the other two as paper seen through both discs. In Fig. 3 the lever’s end points toward you, swung toward the side it opens, since the patent does not say which way the lever points.
Sources
Read in November 2026.
- M. S. Byrne Jr., US Patent 613,024, “Faucet”, 25 October 1898. Fig. 1 is drawn after its second figure.
- A. R. Bonfield Jr., US Patent 925,679, “Compression cock or bib”, 22 June 1909, for which way the handle closes.
- R. G. Parkison (spelled Parkinson on this patent), US Patent 3,810,602, “Ceramic disk faucet”, 14 May 1974, for American Standard, and why washers wear. Its drawings were not used.
- R. G. Parkison, US Patent 3,433,264, “Noise reduction structure for mixing valve”, 18 March 1969, for American Standard, a single-lever valve with ceramic discs. Fig. 3 follows its text.
- A. M. Moen, US Patent 2,373,702, “Faucet”, 17 April 1945, his mixing faucet, read for its text.
- P. Lange for Otto Fluehs, German Patent DE 32 07 895 C2, “Ventiloberteil für Sanitärarmaturen”, 1983, a valve top with two ceramic discs, read in an English machine translation.
- R. T. Williams, US Patent 5,127,438, “Long lasting faucet having minimum wear”, 7 July 1992, a quarter-turn faucet with ceramic discs.
- Consumer Product Safety Commission (US), “Avoiding Tap Water Scalds”, publication 5098, March 2012.
- Wikipedia, “Tap (valve)”, for the 1845 date; British Film Institute, its note on the Chrimes works; M. Wainwright in The Guardian, on Rotherham (23 August 2000).
- Tap Warehouse, “How to Change a Ceramic Disc Cartridge”, for why they leak. Its repair steps are not repeated here.
- DIYdata, “Ceramic water taps for sink, basin or bath explained”. User report.
- Home Improvement Stack Exchange, the question “Why does my bath faucet drip for a few minutes after it’s shut off?”, June 2013, and the answers to it. User report.
- Home Improvement Stack Exchange, “Faucet drip after water shut off”, April 2015. User report.
- Home Improvement Stack Exchange, “What does ‘1/4 turn waterless ceramic disc valve’ mean …”, February 2012. User report.
- Home Improvement Stack Exchange, “Can I leave the hot water pipe to a faucet disconnected?”, April 2022. User report.
- UKClimbing.com forums, “Dripping tap woes”, March 2020. User report.
The type is Playpen Sans by TypeTogether, under the SIL Open Font License 1.1.