Sprinkler
Impact sprinklers are driven round by nothing but the water leaving the nozzle. Beside the nozzle hangs a spring-loaded arm with a small spoon on its end, and the jet keeps knocking that spoon aside. Each time the spring brings the arm back, it strikes the nozzle, and the head moves on a little.
A spoon in the jet
An impact sprinkler’s head turns on a fixed pipe and carries the nozzle. Beside it an arm swings on a pin about the same upright axis as the head. A vane at the arm’s far end sits in front of the nozzle, held there by the arm spring, coiled round the axis. The spoon in these drawings is that vane.
Most of the jet strikes the vane, which turns the water sideways, and the water pushes back on the vane as it leaves. So the arm swings out. The spring slows it, stops it and pulls it back. On the way back the vane cuts through the jet, and the arm strikes the nozzle and turns the whole head through a small part of a turn. The vane is back in the jet. Fig. 1 runs three of these beats at 3 bar, with a graph below of the arm’s swing and the head’s turn. Before you move through the first beat, guess when the head turns: while the arm swings out, or only when it comes back.
What the drawing shows
The head waits for the knock, and nothing else in the beat moves it. In the drawing the spoon leaves the jet 23 thousandths of a second into a beat, and the arm is furthest out, 51°, at 129. It strikes the stop at 247 thousandths. The head then slides on with the arm for another 24 thousandths and stops 5° further round. The drawing works these times and angles out from its model of an arm, a spring and a bearing set to run at 3 bar.
Why the head does not turn back
While the arm swings out, its spring pulls on the head as well, the other way. Orton Englehart dealt with this in his patent of 1935. The head does not turn backwards, he wrote, because the spring resists less than the friction where the head sits on the pipe. That friction comes from the water. The pressure in the supply pipe pushes the head up against a gasket. In the drawing’s model that grip grows with the pressure, and so does the jet’s push. Rain Bird lists bearing washers and an upthrust spring among the parts of its Maxi-Paw heads. In the drawing the bearing would hold 4.3 times the spring’s strongest pull before it slipped.
Big field sprinklers can manage without the coil spring. Smaller impact arm sprinklers typically press the arm into the water with a torsion spring, but the big ones in a 1979 patent for Nelson Irrigation swing the arm on a level pivot, with a counterweight that sends the spoon back into the stream.
Turning back at the ends
A head that goes all the way round waters a whole circle. To water up to a wall or a hedge and no further, as Englehart put it in a second patent, the head must turn back at each end of its arc. He applied for that patent in July 1937, and it was granted in September 1941. Two springy rings grip a fixed collar below the head, and each has a long ear sticking out. A finger hangs down from the head, and as the head turns, the finger meets one ear and then, at the far end, the other. Each meeting rocks a trip over, and a small spring snaps it to one side or the other.
The trip works a stop. It sits at the head’s back. With the stop out of the way, the arm works as in Fig. 1, and the knock on the nozzle turns the head on. With the stop in, a dog behind the arm’s pin strikes it as the arm swings out, so each kick from the water turns the head the other way. The arm swings only a little before the stop catches it, and the spring brings it back too weakly, Englehart wrote, to turn the head forward again. Fig. 2 follows his words, not his drawings, and draws his yoke, rock shaft and snap spring as one lever. Before you run it through a sweep, guess which way the head travels faster.
What the drawing shows
Turning back is the faster way in the drawing, at 27° a second against 18° turning on. Each backward beat lasts 0.15 of a second, because the stop catches the arm when it is 11° out, where turning on lets it swing to 51°. The weak return knock does turn the drawing’s head forward by 0.4° of every 4.6°, and the drawing keeps its model’s figure. Englehart wrote that it would not. The rings are also called arc adjusters, or trip collars, and a trip pin flipped up so that it misses them makes the head go full circle.
Pressure and reach
Rain Bird publishes how far its brass 25BPJ head throws water with each of two nozzles. With the 5/32 inch nozzle, 3.97 mm across, the table runs from 2.1 to 3.5 bar at the nozzle, the head’s whole operating range. The stream leaves at 25° above level and, by the table’s heading, rises 2.1 m. Dividing the table’s flow by the area of the bore gives the speed of the water as it leaves, 19.4 m/s at the low end of the range and 25.9 at the top. Before you raise the pressure in Fig. 3, guess how much further the water lands at the top of the range.
What the drawing shows
The water lands only 0.6 m further out by Rain Bird’s table, 11.9 m at the low end and 12.5 m at the top. The pressure rises by two thirds and the flow by a third, from 0.24 to 0.32 litres a second. The reach grows by only 5%. In the drawing’s model the arm swings further at the higher pressure, 57° against 41°, and the head steps a little further each beat, 5.3° against 4.8°. The friction in the bearing grows with the pressure too, so the steps grow far less than the kicks. Most sprinklers have an upper limit of 80 psi at the head, 5.5 bar, and a head that turns or reverses very fast is a warning of too much pressure.
When the head stops
Impact sprinklers most often stop working from lubricants other than water, low water pressure, dirt in the water, and worn or damaged parts. Any of them can stop the head turning, or leave it turned to one side and failing to come back. Most popular models need at least 25 psi at the last sprinkler on the line, about 1.7 bar. A head that turns to one side and stops can also have a broken trip spring, a missing trip collar or a trip pin left up.
Owners report much the same. In a thread on r/lawncare about a new Orbit head that would not turn back, the reply most liked blamed pressure too low to work the switch that reverses it. Another owner had found that at the end of more than 150 feet of hose. A third said the V-shaped stainless piece that sends the head back sometimes sticks. One owner wrote that metal heads clog and calcify in time, and that plastic ones last longer. On Gardening Stack Exchange, an owner whose impact heads had stopped turning had greased the moving parts, with no change.
Impact or impulse
Englehart, a citrus grower in Glendora, California, filed for a patent on this kind of sprinkler on 18 December 1933, and it was granted on 16 April 1935. Rain Bird calls it the original impact drive sprinkler, and his patent the first of its own. It also says the American Society of Agricultural Engineers named the sprinkler a historic landmark in 1990. The society’s plaque in Glendora adds that Englehart assigned all his rights to his friend Clement LaFetra and LaFetra’s wife, Mary Elizabeth. Production began in the LaFetra family barn on 13 October 1935. The plaque gives the patent’s date as 18 December 1933, the day the application was filed. It spells his name Englehardt.
Rain Bird and the plaque call it an impact sprinkler. Englehart’s second patent calls the moving part an impulse arm, Dramm sells a brass Impulse Sprinkler, and Eden calls one brass head by both names on a single page.
What the drawings leave out
The sizes are the drawing’s own. So are its weights, stiffnesses and friction, chosen to give a few degrees a beat. The drawings look down on the head, so the nozzle’s 25° rise does not show, and the arm is drawn flat over the nozzle.
The model lets the spoon slip back through the jet freely, although Englehart wrote that the water pulls it back in, and it lets each knock finish before the jet pushes again. The water is drawn as pen arrows. In Fig. 2 the parts sit beside one another so that they show, the trip flips at the end of a beat, and the short ear beside each long one, where a screwdriver spreads the ring to move it, is drawn as a stub. No real head was measured for these drawings.
The water’s numbers are Rain Bird’s: the bore, the flows, the reaches, the stream’s height and its 25°, from the table for one head with one nozzle. They are for that head alone, since the pressure a head needs varies from model to model.
Sources
Read in November 2026.
- O. H. Englehart, US Patent 1,997,901, “Water sprinkler”, 16 April 1935, for the arm, vane, spring and stop, and why the head is held. None of its drawings appear here.
- O. H. Englehart, US Patent 2,256,737, “Automatic reversing rotary sprinkler”, 23 September 1941, for the rings, finger, trip and stop. Fig. 2 is drawn from its text.
- L. P. Meyer for Nelson Irrigation, US Patent 4,161,286, “Self-compensating nozzle construction”, 17 July 1979, for the big field sprinklers.
- Rain Bird, “Impact sprinkler troubleshooting guide”, in a copy kept by a distributor, with its parts lists.
- Rain Bird, “25BPJ-FP-ADJ … Brass Impact Sprinklers”, a performance sheet, and “25BPJ Series”.
- Rain Bird, “A legacy of agricultural innovation” and “About Rain Bird: Our History and Mission”.
- Historical Marker Database, “Rain Bird Impact Drive Sprinkler Head”, its transcription of the Glendora plaque of 1990.
- Dramm, “ColorStorm Impulse Sprinkler”; Eden, “Brass Impulse Sprinkler with Step Spike”.
- Gardening & Landscaping Stack Exchange, “Sprinkler system does not rotate”, May 2021, and the answers to it. User report.
- r/lawncare, “Orbit impact sprinkler won’t rotate back”, April 2025, via the Arctic Shift archive. User report.
The type is Playpen Sans by TypeTogether, under the SIL Open Font License 1.1.